Haltech F10 Bedienungsanleitung Seite 83
- Seite / 104
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
78
16.7 Electric Intercooler Fan Control (IF)
This function can be used to switch on an electric f an on the intercooler when the inlet air
temperature exceeds a certain value. The fan will stay on until the temperature drop s below a
second value.
NB: The electric fan cannot be driven directly by the ECU. A relay must be used to switch the
high currents drawn by the fan.
To use this function, you must have the following:
An electric fan, fused and relay switched;
F10 programming software and cab le.
Install the wiring for the intercooler fan to one of the Digital/PWM outputs. This should be
done as described in figure 16.7 for the intercooler fan. Be sure that the relay contacts are
rated higher than the current drawn by the fan.
Run the F10 programming software and go to the Options page. Select the Intercooler Fan
function on the appropriate output and set the two temperatures as required.
Switch On Temperature
The inlet air temperature that must be exceeded to switch the fan on.
Switch Off Temperature
The temperature the inlet air must drop below before the fan will be switched off. This
parameter should be at least 5° lower than the Switch On temperature to prevent the
fan from switching in and out repeatedly.
Figure 16.7. Ex ample circuit for an Intercooler Fan.
- Table Of Contents 1
- Introduction 6
- Before You Begin 7
- Tool/Supply Requirements 8
- How It Works 9
- The F10 and F10A 10
- HALTECH F10 SPECIFICATIONS 11
- – fu el cut 13
- SECTION 1 Getting Started 15
- 1.2 Installation Summary 16
- Mounting 17
- 1.3.7. Power Relays 21
- 1.3.8. Fuse Block Assembly 22
- 1.3.14 Connect the ECU 26
- CHAPTER 2 GETTING ONLINE 27
- 2.2 Ope rating the Software 27
- 2.2.1 Computer Requirements 27
- Dy or %y 28
- LQVWDOOy 28
- 2.4 Using the System ONLINE 30
- 2.5 The Main Menu 30
- 2.6 How to Quit 31
- 2.7 Checking the Engine Data 31
- CHAPTER 3 ECU SETUP 32
- 3.1 ECU Setup 32
- 3.1.2 Main Set-up 32
- 3.1.2 Fuel Setup 33
- 3.1.3 Trigger Set-up 36
- Typical Applications 37
- 4.1 What are maps? 38
- 4.3 Using the Software 38
- 4.4 Accessing the fuel maps 39
- 4.6 Duty Cycles 43
- 4.7 Command Summary for Maps 45
- 5.3.1 Tuning for Idle 47
- 5.3.2 Tuning with No Load 47
- 5.3.3 Loading the Engine 47
- 5.3.4 On the Dyno 48
- 5.3.5 On the Road 48
- 5.3.6 Fine Tuning the Engine 48
- CHAPTER 6 THROTTLE EFFECTS 49
- 6.1 Throttle Response 49
- 6.2 Zero Throttle Map 50
- 6.3 Full Throttle Map 50
- 7.1 Cold Cranking 51
- 7.2 Cold Engine Operation 51
- 8.1 Air Temp Fuel Map 52
- 8.2 The Battery Voltage Map 52
- 8.5 Barometric Correction 53
- Method 3 54
- Method 2 54
- Method 1 55
- Sensing Engine Load by TPS 55
- Completing Method 1 55
- 8.6 Post Start Enrichment 57
- SECTION 3 Software Features 58
- 9.2 Loading Maps and Set-up 59
- 9.3 Upgrading from F9 59
- 9.4 File Management 59
- 9.4.1 Erasing Unwanted Maps 59
- CHAPTER 13 SOFTWARE ACCESS 66
- 13.1 The Input/Output Page 66
- 13.1.2 Aux In and Aux Out 67
- 4 Injectors 68
- 5 Injectors 68
- 6 Injectors 68
- 8 Injectors 68
- 13.2 The Output Options Page 69
- 13.3 The PWM Options Page 69
- 13.4 Enabling Options 69
- 14.1 Description 70
- Engine Cold 72
- Engine Warm 72
- 15.1 Description 74
- CHAPTER 16 PWM OUTPUTS 77
- 16.1 Description 77
- 16.2.1 Description 77
- 16.3.1 Description 79
- 16.12 Turbo Timer (TT) 86
- SECTION 5 Appendices 87
- A.3 Starting problems 89
- A.4 Idling Problems 90
- A.6 Full Powe r Problems 90
- A.8 Cold Running Proble ms 91
- A.9 Fuel Consumption 91
- APPENDIX B FUEL INJECTORS 92
- B.1 Injecto r Impe da nce 92
- B.3 Injector Driver Box 93
- C.1 Fuel Requirement 94
- C.2 Injector Flow Capacity 94
- C.3 Injector Staging 95
- C.4 Fuel Pump Capacity 95
- The S1/S3 Hall Effect Sensor 97
- Fitting the magnets 98
- Ty pica l s e t-ups - S3 99
- LIMITED WARRANTY 102
- APPENDIX E WIRING DIAGRAMS 104
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Für das Auto Haltech F10
Für das Auto Haltech IG5 Bedienungsanleitung
(89 Seiten)
(89 Seiten)
Für das Auto Haltech E6A Bedienungsanleitung
(126 Seiten)
(126 Seiten)
Für das Auto Haltech E6S Bedienungsanleitung
(134 Seiten)
(134 Seiten)
Für das Auto Haltech E6GMX Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Für das Auto Haltech E6M Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Für das Auto Haltech E6K Bedienungsanleitung
(154 Seiten)
(154 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Elevating decks in mountainous areas through the careful integration of planters and lively greenery introduces a invigorating touch of nature to living in the mountains. Engaging in talks about the individual types of plants that flourish in mountainous settings, investigating suitable planter options, and considering design aspects provide useful guidance for individuals looking for to create green and welcoming outdoor spaces. Through the exchanged experiences of forum members, taking into ac