Haltech F10 Bedienungsanleitung Seite 19
- Seite / 104
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
14
1.3.3. Inlet Air Temperature Sensor
The air temperature sensor is used to comp ensate for changes in air density due to air
temperature. Cold air is denser than warm air and therefore requires a greater volume of fuel
to maintain the same air/fuel ratio. This effect is most noticeable in forced induction engines.
The Haltech F10 will automatically comp ensate using the signal received from the air
temperature sensor.
The sensor should be mounted to provide the best representation of the actual temperature of
the air enterin g the combustion chamber, i.e. after any turbo or supercharger, and intercooler,
and as close to the head as possible. The sensor needs to be in the moving air stream to give
fast response times and reduce heat-soak effects.
Note: The Haltech air temp erature sensor will read temperatures up to 120° C
and temperatures above this will be interpreted as a fault condition. The air
temperature after some turbos and superchargers can exceed this. If this occurs
with your engine you should consider fitting an intercooler to reduce air
temperature and increase ch ar ge density . If this is not possible then the air
temperature sensor should be placed up stream of the turbo or sup ercharger to
monitor ambient air temp erature.
Once a suitable position has been located for the air temperature sensor a hole should be
drilled and tapp ed to accep t the sensor. Remove the manifold or in let tract from the engine
before machining the sensor mount. Do not allow any metal particles to enter the inlet
manifold of the engine as these will be drawn into the engine and damage it. Wash all
components before reassembly.
- Table Of Contents 1
- Introduction 6
- Before You Begin 7
- Tool/Supply Requirements 8
- How It Works 9
- The F10 and F10A 10
- HALTECH F10 SPECIFICATIONS 11
- – fu el cut 13
- SECTION 1 Getting Started 15
- 1.2 Installation Summary 16
- Mounting 17
- 1.3.7. Power Relays 21
- 1.3.8. Fuse Block Assembly 22
- 1.3.14 Connect the ECU 26
- CHAPTER 2 GETTING ONLINE 27
- 2.2 Ope rating the Software 27
- 2.2.1 Computer Requirements 27
- Dy or %y 28
- LQVWDOOy 28
- 2.4 Using the System ONLINE 30
- 2.5 The Main Menu 30
- 2.6 How to Quit 31
- 2.7 Checking the Engine Data 31
- CHAPTER 3 ECU SETUP 32
- 3.1 ECU Setup 32
- 3.1.2 Main Set-up 32
- 3.1.2 Fuel Setup 33
- 3.1.3 Trigger Set-up 36
- Typical Applications 37
- 4.1 What are maps? 38
- 4.3 Using the Software 38
- 4.4 Accessing the fuel maps 39
- 4.6 Duty Cycles 43
- 4.7 Command Summary for Maps 45
- 5.3.1 Tuning for Idle 47
- 5.3.2 Tuning with No Load 47
- 5.3.3 Loading the Engine 47
- 5.3.4 On the Dyno 48
- 5.3.5 On the Road 48
- 5.3.6 Fine Tuning the Engine 48
- CHAPTER 6 THROTTLE EFFECTS 49
- 6.1 Throttle Response 49
- 6.2 Zero Throttle Map 50
- 6.3 Full Throttle Map 50
- 7.1 Cold Cranking 51
- 7.2 Cold Engine Operation 51
- 8.1 Air Temp Fuel Map 52
- 8.2 The Battery Voltage Map 52
- 8.5 Barometric Correction 53
- Method 3 54
- Method 2 54
- Method 1 55
- Sensing Engine Load by TPS 55
- Completing Method 1 55
- 8.6 Post Start Enrichment 57
- SECTION 3 Software Features 58
- 9.2 Loading Maps and Set-up 59
- 9.3 Upgrading from F9 59
- 9.4 File Management 59
- 9.4.1 Erasing Unwanted Maps 59
- CHAPTER 13 SOFTWARE ACCESS 66
- 13.1 The Input/Output Page 66
- 13.1.2 Aux In and Aux Out 67
- 4 Injectors 68
- 5 Injectors 68
- 6 Injectors 68
- 8 Injectors 68
- 13.2 The Output Options Page 69
- 13.3 The PWM Options Page 69
- 13.4 Enabling Options 69
- 14.1 Description 70
- Engine Cold 72
- Engine Warm 72
- 15.1 Description 74
- CHAPTER 16 PWM OUTPUTS 77
- 16.1 Description 77
- 16.2.1 Description 77
- 16.3.1 Description 79
- 16.12 Turbo Timer (TT) 86
- SECTION 5 Appendices 87
- A.3 Starting problems 89
- A.4 Idling Problems 90
- A.6 Full Powe r Problems 90
- A.8 Cold Running Proble ms 91
- A.9 Fuel Consumption 91
- APPENDIX B FUEL INJECTORS 92
- B.1 Injecto r Impe da nce 92
- B.3 Injector Driver Box 93
- C.1 Fuel Requirement 94
- C.2 Injector Flow Capacity 94
- C.3 Injector Staging 95
- C.4 Fuel Pump Capacity 95
- The S1/S3 Hall Effect Sensor 97
- Fitting the magnets 98
- Ty pica l s e t-ups - S3 99
- LIMITED WARRANTY 102
- APPENDIX E WIRING DIAGRAMS 104
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Für das Auto Haltech F10
Für das Auto Haltech IG5 Bedienungsanleitung
(89 Seiten)
(89 Seiten)
Für das Auto Haltech E6A Bedienungsanleitung
(126 Seiten)
(126 Seiten)
Für das Auto Haltech E6S Bedienungsanleitung
(134 Seiten)
(134 Seiten)
Für das Auto Haltech E6GMX Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Für das Auto Haltech E6M Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Für das Auto Haltech E6K Bedienungsanleitung
(154 Seiten)
(154 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Elevating decks in mountainous areas through the careful integration of planters and lively greenery introduces a invigorating touch of nature to living in the mountains. Engaging in talks about the individual types of plants that flourish in mountainous settings, investigating suitable planter options, and considering design aspects provide useful guidance for individuals looking for to create green and welcoming outdoor spaces. Through the exchanged experiences of forum members, taking into ac