Haltech E6GMX Bedienungsanleitung Seite 35
- Seite / 114
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
E6GMX Manual
35
4.2.5 The In/Out Set-up Page
The In/Out set-up page contains the information about auxiliary components the ECU is to
control. The In/Out Set-up Page is accessed via the set-up menu or using: CTRL-N from
anywhere in the programming software.
The fields in the ignition set-up page are as follows:
Trim Control (Pin E6)
The optional Trim is a useful tuning and control unit and can be used to control one of
several parameters. If there is nothing connected to the trim plug, the trim will have
no effect (except with boost control). The available functions are:
Fuel (Fine) ±12.5% adjustment of fuel.
Fuel (Coarse) ±50% adjustment of fuel.
Ignition +7 to -8 degrees adjustment of ignition advance.
Ignition Trailing +7 to -8° adjustment for Rotaries only
Boost Control Boost trim for Waste-gate control only.
BAC2 This trims the idle speed by modifying the duty cycle driving
the BAC valve through PWM 3 or 4 when set to BAC2 Valve
(open loop idle control). When the spare A/D is set to BAC2 it
overrides all BAC2 PWM parameters and drives the channel
with a duty cycle proportional to the trim position.
Spare Input Function (Pin E3)
The Spare input is an analogue input similar to the Trim Control input that can be
configured for one of several tasks. The available functions are :
General 0-5 volt input; no effect on ECU operation.
Fuel (Fine ±12.5% adjustment of fuel.
Fuel (Coarse ±50% adjustment of fuel.
Ignition Trim +7 to -8 degrees adjustment of ignition advance.
Ign Trailing Trim +7 to -8° adjustment for Rotaries only.
Baro Sensor Barometric Pressure Sensor (internal/external).
Exhaust MAP Sensor Exhaust Pressure(does not affect ECU operation)
Aux RPM Limit Input switch for activating Aux RPM limit. Limit may be
above/below the primary RPM limit. Useful for launching
or allowing extra RPM momentarily for overtaking.
O2 Sensor Display only (does not affect ECU operation). The reading
appears on the Engine Data Page as mV.
- Warnings 1
- Contents 2
- Introduction 7
- Before You Begin 8
- How It Works 10
- SECTION 1 Getting Started 11
- 1.2.4 Connect the ECU 12
- 2.1 Computer Requirements 13
- 2.2 Operating the Software 13
- 2.2.2 Running the Software 15
- 3.1 The Menu Structure 16
- 3.1.1 The File Menu 16
- 3.1.1.1 Load From File 17
- 3.1.1.2 Save To File 17
- 3.1.1.4 Quit 18
- 3.1.2 The Map Menu 19
- 3.1.2.2 Ignition Maps 20
- 3.1.2.3 Fuel Correction Maps 21
- 3.1.3 The Set-up Menu 22
- 3.1.4 The Options Menu 22
- 3.1.5 Data Page Menu 22
- 3.1.6 Password Protection 23
- 3.2.1 Going Online 24
- 3.3 Hot Key Summary 26
- 4.2 The ECU Set-up Pages 27
- 4.2.1 Main Set-up Page 27
- 4.2.2 Fuel Set-up Page 29
- 4.2.3 Ignition Set-up Page 32
- 4.2.4 Trigger Setup 34
- 4.2.5 The In/Out Set-up Page 35
- HALTECH MAPS 38
- 4.3 What are Maps? 38
- 4.4.2 All Ranges 40
- 4.4.3 Percentage Changes 40
- 4.4.4 Linearise 41
- 4.4.5 Numeric Mode 43
- 4.4.6 3D View 44
- 4.5 The Haltech Maps 45
- 4.5.3 Fuel Correction Map 45
- 4.5.5 Zero Throttle Map 47
- 4.5.6 Full Throttle Map 47
- 4.5.7 Turbo Waste-gate Maps 48
- 4.6 Dual Maps 48
- 4.6.1 Editing Dual Maps 49
- SECTION2 Tuning The Engine 50
- 5.5.4 Tuning for Idle 53
- 5.5.5 Tuning with No Load 53
- 5.5.6 Loading the Engine 53
- 5.5.7 Fine Tuning the Engine 54
- CHAPTER 6 THROTTLE EFFECTS 55
- 6.1 Throttle Response 55
- 6.2 Zero Throttle Map 56
- 6.3 Full Throttle Map 56
- 7.1 Cold Cranking 57
- 8.1 Fuel Versus Air Temp Map 58
- 8.2 The Battery Voltage Map 58
- 8.3 The Ignition Coolant Map 58
- 8.5 Barometric Correction 59
- 8.6 Post Start Enrichment 62
- SECTION 3 Software Features 63
- 9.1.3 Logging the Data 64
- 9.1.4 Displaying The Data 65
- 9.1.4.1 Displaying Channels 66
- 9.1.4.4 Removing A Dataset 67
- 9.1.4.5 Data Values 68
- 9.1.4.6 Zooming 68
- 10.1 Idle Speed Control and O 72
- Closed Loop Control 72
- 10.1.1 Idle Control 72
- 10.2 The PWM Options Page 76
- 11.10 Turbo Timer (TT) 82
- 11.11 NOS Switch 82
- 11.12 Anti-Lag Switch 83
- 11.13 Air Conditioning 84
- 11.14 Engine Control Relay 84
- 11.15 VTEC 85
- 11.16 BAC2 85
- 11.18 TPS Switch 86
- SECTION 5 Appendices 88
- A.1 Control Program Problems 89
- A.3 Starting problems 90
- A.4 Idling Problems 90
- A.6 Full Power Problems 91
- A.8 Cold Running Problems 91
- A.9 Fuel Consumption 91
- Ignition 92
- B.7 Ignition Outputs 93
- Constant Duty 93
- Constant Charge 94
- APPENDIX C INJECTORS 100
- C.1 Injector Impedance 100
- C.2 The Injector Drivers 101
- APPENDIX D FUEL SYSTEMS 102
- D.1 Duty Cycles 102
- D.2 Fuel Requirement 104
- D.3 Injector Flow Capacity 104
- D.4 Fuel Pump Capacity 105
- E.1 Trigger Edge 106
- E.2 Trigger Angle 108
- E.3 Trigger Pull up 109
- E6GMX Manual 113
- E6GMX Hardware Options 113
- LIMITED WARRANTY 114
Verwandte Produkte und Handbücher für Für das Auto Haltech E6GMX
Für das Auto Haltech E6M Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Für das Auto Haltech E6K Bedienungsanleitung
(154 Seiten)
(154 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.799 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern